MM Aqua & Munters Fills Dealer

Name: MM Aqua Cooling Tower Fills
Brand: MM Aqua

The MM Aqua range of Munters-designed cooling tower media. It includes C-series and vertical-flute film fill, trickle grid and V-bar splash fill, drift and mist eliminators and distribution nozzles. We supply against your model number or your tower data.

Get a Quote on WhatsApp Email Us for a Quote [email protected]+91 79048 17415

See Products

Close-up stacks of black corrugated MM Aqua cooling tower fill media at a plant

Black Munters cooling tower fill packs stacked in a plant yard below overhead conveyors

Munters-designed film fill media
C10.12 through C10.27 and VFO-20
Drift and mist eliminators, nozzles
Media to CTI STD 136 (2010)

About Us

Since 2016, CJP has supplied, manufactured and serviced plate heat exchangers for industry and OEMs across India. From our Chennai works we make gasketed units, cooling tower fills and replacement plates and gaskets, and our crews install and service them.

MM Aqua & Munters Fills Dealer

We are a dealer for MM Aqua and Munters fills, and match the specification to your model designation or tower data.

More about CJP

10Years of experience

310+Clients

800+Projects delivered

Our Clients

Products

MM Aqua & Munters Fills Dealer

A tower built around branded media is usually refilled by model, not by description. A C10.19 pack is not a C10.12 pack. A drift eliminator of a different pitch will not sit on the existing supports. The range below is listed by MM Aqua designation, with the figures the manufacturer publishes. You can match a specification before you order.

Send the model designation from the existing media if you have it. If not, send your tower data and water quality.

Film Fill — C Series

Cross-corrugated virgin PVC, UV protected, to CTI STD 136 (2010). Choose the flute size by the water, not the duty: a finer flute gives more surface area but needs cleaner water. Standard pack L 1200 × W 300 × H 300 mm. Supports max. 1000 mm apart, at least 50 mm wide.

4 models

C10.1212 mm flute, 243 m²/m³. HVAC and process cooling on clean water to TSS <20 ppm. Sheet 0.175–0.25 mm, single or double edge fold. Min. water load 8 m³/m²/h.

C10.1919 mm flute, 148 m²/m³. Power, petrochemical, refinery and steel duties to TSS <80 ppm. Sheet 0.20–0.40 mm, double edge fold mandatory. Min. water load 5 m³/m²/h.

C10.2525 mm angular flute, 112 m²/m³. Raw river and sea water to TSS 200 ppm. Sheet 0.30–0.45 mm. Continuous operation at 55 °C or less. Min. water load 3 m³/m²/h. Tested to 2.1 m multilayer.

C10.2727 mm angular flute, 112 m²/m³. Raw river and sea water to TSS 200 ppm. Sheet 0.30–0.45 mm. Continuous operation at 55 °C or less. Min. water load 3 m³/m²/h. Tested to 2.1 m multilayer.

Film Fill — Vertical & Offset Flute

For duties where fouling is the main problem, not thermal performance. Vertical channels pass solids that would bridge a cross-corrugated pack. Virgin PVC, with supports max. 1000 mm apart, at least 50 mm wide.

2 models

VF 10.19Vertical flute, 148 m²/m³. Straight channels discharge solids and limit biofilm build-up; self-supporting on sharp-edged corners. Pack L 1200 × W 300 × H 300 mm. Min. water load 5 m³/m²/h.

VFO-2020 mm offset vertical flute, 150.5 m²/m³. The offset path keeps redistributing water, raising turbulence at low pressure drop. Pack L 2000 × W 300 × H 500/600 mm. Min. water load 5 m³/m²/h.

Splash Fill

For water that would foul a film pack: high solids, oil and grease, or temperatures above what PVC film media can take.

3 models

MMA NC20Trickle grid fill in polypropylene, assembled mechanically without adhesive. 908 × 450 × 305–610 mm, 1.8 mm material, 20 mm sheet spacing, black. TSS to 300 ppm, 80–85 °C. CTI ATC 136 (2010).

V-BarExtruded PVC splash bar, 85 × 65 mm, with a straight strengthening rib and V-bar support to bench tie. Rhombus or round punches. To 55 °C.

Turbo SplashBaffles about 50 mm apart, for brackish and algae-prone water. TSS above 500 ppm with no upper limit. Oil or grease below 500 ppm. Up to 110 °C.

Drift Eliminators

Pitch and support span decide what fits. All three are rated to 55 °C.

3 models

D-15Cellular PVC, drift loss 0.001% of circulating water. Max face velocity 4.5 m/s, drag coefficient 2.2. Supports max 600 mm apart, 10 mm wide. Shipped nested and glued into blocks on site.

D-31Profile PVC on injection-moulded spacers, 37 mm pitch, lengths to 5000 mm. Drift loss 0.007%. Max face velocity 3.5 m/s, drag coefficient 2.15. Supports max 1500 mm apart, 50 mm wide. Can be pressure washed.

SpectraDouble-wall profile on injection-moulded spacers, 69.85 or 76 mm pitch. Drift loss 0.001–0.003%. Glue-free, spans to 3 m end support, hooked profile at air exit. Disassembles for cleaning.

Mist Eliminators

Droplet separation profiles. Send the designation, or measure the profile depth of what is fitted now.

6 models

T-100Profile depth 170 mm, up to 5000 mm long, PVC. Works as a mist eliminator and as an air straightener.

T-200Profile depth 150 mm, up to 5000 mm long, PVC.

T-400Profile depth 150 mm, up to 5000 mm long, PVC.

BMEProfile depth 280 mm, up to 5000 mm long, PVC.

LTGProfile depth 214 mm, up to 5000 mm long, PVC.

DV-270Vane-type impingement separator for vertical gas flow, with low pressure drop. Collected liquid drains off the plates by gravity.

Distribution Nozzles

Water distribution for counterflow towers, and for bio-tower and trickling filter duties.

3 models

H-NozzleNon-clogging counterflow nozzle in 7 orifice sizes from 0.75" to 1.5", colour coded. It sits on a 2" bolted collar that unthreads for cleaning. Works best between 1 and 1.5 psi.

NP-30Fixed nozzle for distribution over bio-tower and trickling filter media, including up-flow distribution. Suits circular, square and rectangular plans.

Flower NozzleCorrosion-resistant plastic with a rectangular distribution pattern and little overlap. You change capacity within one body. The twist-lock fit needs no tools.

Send Us the Details

Send the model designation from the existing media if you have it. If not, send your tower data and water quality.

Start an enquiry on WhatsApp Email Us for a Quote [email protected]+91 79048 17415

For purchasing teams

Frequently Asked Questions

01How do we choose the right fill for our tower?

The water quality and the tower supports decide it. Send us the tower type (RCC or FRP), the dimensions, the circulating water flow, the hot and cold water temperatures and the design wet bulb. Tell us the suspended solids and the water treatment in use. We recommend film fill for clean water and splash fill where solids would block a film pack.

02Can you supply a fill to match what is in our tower now?

Yes. Send a photo of the current fill on its supports, and its model designation if you have it. Add the support spacing or bench tie layout. We match the type, pack size and fit to the existing supports.

03How do we work out the quantity?

From the fill volume in the tower: internal length, width and fill height. You can quote the quantity in cubic metres or in pieces. If you are not sure, send the tower dimensions and we calculate it for you.

04Do you deliver, and can you remove the old fill?

We quote freight to your plant with the fill. Tell us the tower location and whether you want the old fill removed. We confirm delivery timing with the quotation.

Talk to a Specialist

Message us on WhatsApp or email. We help you choose the right product.

Chat on WhatsApp Email Us for a Quote [email protected]+91 79048 17415